FAQ malunga neCO2 laser macbine ngexesha lokusetyenziswa kunye nendlela yokusombulula? (二)

六、 Ubunzulu obahlukeneyo bomzantsi xa ukrolwa.

1) Isantya sokucwangcisa sikhawuleza kakhulu, amandla okukrola ityhubhu yelaser mancinci kakhulu, hlengahlengisa isantya sokukrola kwaye unyuse amandla okukrola ngexesha.

2) Uxinzelelo lomoya ovuthuzayo olungalunganga lubangela ukuba umgubo wokucutshungulwa unamathele kwaye wenze iiprotrusions zomgca othe tye.

3）Indlela yokubona itenxile okanye ubude bokujongisisa akulunganga, okukhokelela kwimiqadi ethe saa kunye nomzantsi ongalinganiyo.

4）Ukukhethwa kweenkcukacha zelensi ezigxininisiweyo akukho ngqiqweni, kwaye iilensi ezimfutshane zobude obugxininisiweyo kufuneka zikhethwe kangangoko kunokwenzeka ukuphucula umgangatho we-beam.

5) Ubungakanani betyhubhu yelaser ayifanelekanga ukukrola okanye ukusika.

6) Nokuba ukuchaneka kokuskena kuncinci kakhulu, ngokubanzi malunga ne-0.05-0.08.

7) Jonga ukuba i-lens imdaka kakhulu okanye yonakele, kwaye kufuneka icoce okanye ibuyisele ilensi.Nokuba indlela yokubona ivaliwe okanye hayi, yilungise ngexesha.

8) Jonga ukuba i-laser ammeter inokufikelela kwi-16ma, ukuba akunjalo, hlengahlengisa unikezelo lwamandla e-laser okanye ubuyisele umbane welaser.

9) Ukuba umsinga unokufikelela malunga ne-20ma, kodwa ubunzulu abukwanelanga, oko kuthetha ukuba ityhubhu yelaser iyaguga, kwaye ityhubhu yelaser ifuna ukutshintshwa.

 

七、 Isenzeko sokukrolwa okulahlekileyo, ukukrola okungahleliwe, ukuyeka ukukrola, njl.

 

I-1) Ibhodi yokulawula ukuphazamiseka kwe-Electrostatic, nceda ujonge imeko yokumisa umatshini, kwaye ulinganise ukuba ucingo lomhlaba ludibana nomgangatho (ukumelana nomhlaba akufanele kube mkhulu kune-5 ohms).Ukuba ayihambisani nomgangatho, ucingo lomhlaba kufuneka lutshintshwe ukuze luhlangabezane nemigangatho efanelekileyo.

2) Jonga ukuba ngaba ucingo loqhagamshelwano lwebhokisi yolawulo lukhululekile okanye amaqhosha akwindawo yolawulo akuqhagamshelwano olubi.

3) Nokuba kukho umbane owomeleleyo kunye nemagnethi eyomeleleyo kwindawo yomatshini.

4) Jonga ukuba kukho naziphi na iimpazamo kwimizobo yoqobo, enje ngemizobo enqamlezileyo, ayivalwanga, imivumbo engekhoyo, njl. njl., Lungisa iimpazamo kwimizobo, emva koko ukhuphe uvavanyo.

5) Jonga ukuba ityhubhu yelaser okanye unikezelo lwamandla lwelaser luyatshisa okanye luqhawule unikezelo lwamandla lwelaser kuvavanyo.

6) Ingxaki isekhona, vavanya kwakhona emva kokutshintsha i-motherboard kunye nekhompyuter.

 

八, Ukuchithwa komatshini

1) Jonga ukuba ibhanti ye-XY axis iqinile okanye hayi, hlengahlengisa ukutsalwa kwebhanti, kwaye ukuxinana kwebhanti akufuneki kwahluke kakhulu.

2) Yandisa umzobo woqobo kwisoftware yemveliso ukujonga ukuba umzobo ngokwawo ususiwe na.Lungisa iimpazamo kwimizobo yoqobo.

3）Jonga ukuba ibhanti lexesha likhululeke kakhulu na, kwaye nokuba amabhanti kumacala omabini omthi aneqondo elifanayo loxinzelelo.Lungisa ukuqina kwebhanti ye-synchronous, nokuba kukho i-gap phakathi kwe-motor kunye ne-synchronous wheel of the shaft transmission, nokuba ii-chips ezimnyama zevili lokutshixa i-synchronous zikhululekile okanye zichasene nebhanti, kwaye ziqinise ivili elihambelanayo.

4）Jonga ukuba ngaba kukho impazamo enkulu phakathi kokunxulunyaniswa komqadi kunye ne-perpendicularity ye-Y-axis.

5) Nokuba ibhanti linxitywa kakhulu, kwaye nokuba iigiya ziyatyibilika.

6) Isantya sokucubungula sikhawuleza kakhulu, kwaye inyathelo lokulahleka kwenyathelo lenzeka xa i-drive isebenza.

 

九, Iintetho ezibukhali xa ukrola okanye usikwa.

I-1) Ukuba isantya sokusebenza sikhawuleza kakhulu, indawo yokusika yezinto ezicwangcisiweyo iya kubonakala i-serrated, kwaye isantya sokucubungula kufuneka sincitshiswe.

2) Ukuba imveliso ikwifomathi yebitmap ye-BMP, khangela ukuba isisombululo segrafiki sincinane kakhulu.Kwisiseko sokuba ubungakanani begrafiki buchanekile, zama ukwandisa isisombululo kangangoko.

3） Nokuba ibhanti ye-synchronous phakathi kwentloko ye-laser kunye ne-beam iqinile kakhulu okanye ikhululekile kakhulu, hlengahlengisa ukunyanzeliswa kwebhanti ye-synchronous.

4）Jonga i-X-direction pulley, nokuba kukho umsantsa ngenxa yokuguga, buyisela ipuli okanye ibhanti.

5) Kwimeko yokumisa, jonga ukuba ngaba kukho nawuphi na umsantsa phakathi kwentloko yelaser okanye isilayidi.Faka indawo yesilayidi okanye uqinise intloko ye-laser.

6）Jonga ukuba i-lens ebonakalisayo kunye ne-lens yokugxila ikhululekile, kwaye uqinise ilensi evulekileyo.

7) Jonga ukuba ibhanti le-Y-axis liqinile okanye hayi, hlengahlengisa ukutsalwa kwebhanti, kwaye ukuxinana kwebhanti akufuneki kwahluke kakhulu.

 

十、IAlarm yeChiller yamanzi

1) Ukuba i-voltage iphantsi kakhulu, inokubangela ukuba i-chiller ivuse.Qinisekisa ukuba i-voltage efunekayo iyinto eqhelekileyo, kwaye i-voltage stabilizer ingasetyenziswa xa kuyimfuneko.

2) Jonga ukuba umthamo wamanzi kwindawo epholileyo ufikelela kumgca oqhelekileyo, ukuba umthamo wamanzi uphantsi kakhulu, i-alamu iya kukhutshwa, kwaye amanzi acocekileyo aya kuzaliswa.

3）Ukuba umbhobho wamanzi uvaliwe okanye uthotyiwe, nokuba ukhuseleko lwamanzi luvalekile, ukonyuka kokumelana nokuhamba kwamanzi kuya kubangela i-alamu, ukucoca okanye ukulungisa umbhobho wamanzi kunye nokukhuselwa kwamanzi.

4）Khangela ukuba ingaba impompo yamanzi kwi-chiller iqhelekile na, akukho manzi okanye ukuhamba kwamanzi kuncinci kakhulu, buyisela i-chiller.